Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
Almost everyone will have his or her own thinking involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a new one is also a reasonably difficult job. If the old bathtub is conveniently available, the job can relocate rapidly; if you need to open up a wall to eliminate the old tub and also place the new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to think about utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your restroom if you have already purchased a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your devices and product checklist must make up the following:
Preparing for the Setup
Firstly, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to prevent stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before carrying on to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bathtub until the spirit level reads level.
To set up faucets, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water supply and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and additionally check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making certain that the washers are in area between the tap and the sink. Protect the tap in position with the producer provided backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type must be linked to the faucet ends initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack a stiff seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water before securing, to enable the motion experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles using water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on a different web blog. Those who enjoyed our blog posting please remember to pass it around. Thank you for your time. Visit us again soon.
Order Repair Report this page